Twin hose regulators
The most striking and well recognized example of vintage scuba gear is the twin-hose or double hose regulator, a popular style of regulator in the early years of scuba diving, since Jacques-Yves Cousteau and Emile Gagnan pioneered the first such design, the C45 Scaphandre Autonome, which was marketed in the USA (along with a tank and harness) as the Aqua-Lung. The durability of the regulators from the 1950s through the early 1970s lent them to easily be refurbished and restored. Since 2007, Vintage Double Hose, in Wesley Chapel, Florida, has been manufacturing parts for original regulators as well as a modern version of the double-hose scuba regulator. The regulator is composed of modern polymers and specialty metals.[clarification needed] It allows for additional scuba equipment to be attached, such as a submersible pressure gauge, which overcomes one of the problems of the original double hose regulators which were not able to incorporate accessories.
Regulator features of historical interest
First stage with integral reserve valve
A number of manufacturers produced integral reserve regulators in 1961 and 1962 with reasonable market acceptance. These regulators provided a lever operated mechanical reserve valve that restricted air flow when the pressure was below 500 psi. Alerted to having a low gas supply the diver would pull a rod to open the reserve valve and surface using the remaining gas. This feature provides reserve capacity on cylinders with plain valves. With this arrangement the reserve rod must also be transferred to the cylinder in use.:166,167
Twin-hose with regulator on chest
In this unusual configuration the cylinder(s) are on the diver's back and are connected by a low pressure hose to a twin-hose regulator on the diver's chest.
- A design described in Practical Mechanics magazine in January 1955 as a home-made aqualung with a first-stage on the cylinder top leading through a low pressure hose to a large round second-stage (a converted Calor Gas regulator) on the diver's chest connected to the diver's mouthpiece by a twin-hose loop.
- An early Australian design called a Lawson Lung was made in Sydney by a group of enthusiasts who were unable to get Aqua-lungs due to limited supply, based on the patented Costeau-Gagnan design, but modified to use available components. The regulators were made and tested at John Lawson’s jewellery factory in Greenwich, North Sydney. Only 12 were made, and had to be mounted on the chest to achieve acceptable performance. 
Full-face mask regulator
There have been some cases of a single-hose regulator final stage built into a full-face mask so that the mask's big front window, in conjunction with a flexible rubber seal joining it to its frame, functioned as a large and sensitive regulator diaphragm:
- Several versions of the Le Prieur breathing set. Yves Le Prieur first patented with Maurice Fernez, in 1926, a breathing apparatus using a mouthpiece, but as of 1933 he removed the mouthpiece and included a circular full-face mask in all following patents (like 1937, 1946 or 1947).
- In 1934 René Commeinhes, from Alsace (France), adapted a Rouquayrol-Denayrouze apparatus for the use of firefighters. With new 1937 and 1942 patents (GC37 and GC42), his son Georges adapted this invention to underwater breathing by means of a single hose connected to a full-face mask.
- Captain Trevor Hampton invented independently from Le Prieur a similar regulator-mask in the 1950s and submitted it for patent. The Royal Navy requisitioned the patent, but found no use for it and eventually released it. By then, the technology had advanced and it was too late to make this regulator-mask in bulk for sale.
Regulator models of historical interest
Ohgushi's Peerless Respirator
Invented in 1916 by Riichi Watanabi and the blacksmith Kinzo Ohgushi, and used with either surface supplied air or a 150 bar steel scuba cylinder holding 1000 litres free air, the valve supplied air to a mask over the diver's nose and eyes and the demand valve was operated by the diver's teeth. Gas flow rate was proportional to bite force. The breathing apparatus was used successfully for fishing and salvage work and by the military Japanese Underwater Unit until the end of the Pacific War.
These unusual regulators were designed by Robert J. Dempster and made at his factory in Illinois, USA, from 1961 to 1965. The Demone Mark I and Demone Mark II are both two-stage regulators. The second-stage looks like the mouthpiece of a twin-hose regulator but has a small diaphragm on the front. The second-stage valve is inside the mouthpiece tube. The exhaled air goes into a corrugated coaxial exhaust hose which surrounds the low pressure hose and discharges about 60% of the way back to the first-stage to keep the bubbles away from the diver's face. Near the mouthpiece is a one-way valve to let outside water into the exhaust hose to avoid free flow if the diaphragm (at the mouth) is below the open end of the exhaust hose. The Mark I has hoses only on one side, and the Mark II has twinned low pressure hoses, each with its own coaxial exhaust hose and second stage, one assembly on each side of the diver's head, but with both second stages in the same mouthpiece housing and operated by the same diaphragm.:93–100 This version has a small second stage.
Normalair breathing apparatus
This system is unusual in that it used a single stage single hose demand valve in a full-face mask. The high pressure supply hose routes over the shoulder, but from an inverted cylinder, which allows the user to easily reach the valve.:249–253
Dräger Delfin II (Barakuda)
For a few years in the mid-1950s, Dräger made the Dräger Delfin II (their first scuba regulator - it was marketed as the Barakuda (now IAC) in the USA): this was a single stage single hose "pendulum"" regulator with only one ambient pressure (corrugated) hose: the exhaled air went back down the hose to the cylinder mounted regulator and was released to outside through a one-way valve inside the casing. The end of the flexible tube was connected to the mouthpiece by a short quarter-circle of hard tube. The two way hose would have caused dead space similar to a rebreather with a pendulum system.
The first single-hose open-circuit scuba made by Ted Eldred in Melbourne, Australia. It was designed in 1948 to avoid the Cousteau-Gagnan aqua-lung patent, and to get rid of air supply restrictions that affected early Cousteau-Gagnan-type aqua-lungs. Commercial production started in 1952. The Royal Australian Navy adopted it, and it popular with Australian recreational scuba divers. The model CA-1 was used on one cylinder with its valve at the bottom, strapped directly to the back with rucksack-type straps without backpack plate or buoyancy aid, with a single-hose regulator-mouthpiece which could be strapped in. The tank was inverted so that the diver could reach the regulator mounted reserve handle. The head strap was intended to keep the demand valve from falling well below the diver, if dropped from the mouth. The high-pressure regulator screwed into the outlet of the cylinder valve. Versions were made for the Australian Navy until 1976, and the last one known to be sold to the public was sold in that year. About 12,000 Porpoise units of all models were produced, of which about 50 still exist. Only a few of the early models are known today, the rarest being the CA-2, made for use with two tanks.[clarification needed]
- Porpoise oxygen rebreather
This section needs expansion. You can help by adding to it. (February 2020)
Exotic and experimental equipment
Propulsive power from the stored energy
The concept of a diving regulator where the energy released as the air expands from cylinder pressure to the surrounding pressure as the diver inhales, is used to power a propeller has been patented, but no product ever appeared on the market.
Twin-hose, home-made regulators
In 1956 and for some years afterwards in Britain, factory-made aqualungs were very expensive, and many aqualungs of this type were made by sport divers in diving clubs' workshops, using miscellaneous industrial and war-surplus parts. One necessary raw material was a Calor Gas bottled butane gas regulator, whose 1950s version was like an aqualung regulator's second stage but passed gas all the time because its diaphragm was spring-loaded; conversion included changing the spring and making several big holes in the wet-side casing. The cylinder was often an ex-RAF pilot's oxygen cylinder; some of these cylinders were called tadpoles from their shape.
Practical Mechanics design
A design was described in Practical Mechanics magazine in January 1955, for a home-made aqualung with a first-stage on the cylinder top leading through a low pressure hose to a converted Calor Gas regulator on the diver's chest connected to the diver's mouthpiece by a twin-hose loop.
The Nemrod Snark III silver regulator is typical of the older twin-hose type.
- "Vintage Scuba". 2014. Retrieved 6 April 2015.
- Roberts, Fred M. (1963). Basic Scuba. Self-Contained Underwater Breathing Apparatus: Its Operation, Maintenance and Use (Enlarged Second ed.). New York: Van Nostrand Reinhold Co. ISBN 0-442-26824-6.
- Fearon, E. T. "Making an aqualung: How to construct your own underwater breathing apparatus" (PDF). Archived from the original (PDF) on 28 September 2007. Retrieved 29 September 2007.First published in: Newnes Practical Mechanics, January 1955
- Eldred, Tony. "Lawson Lung (Australia)". www.frogmanmuseum.com. Dominique Breheret. Retrieved 16 November 2016.
- "The Lawson Lung". www.divesrap.com. Retrieved 24 August 2017.
- Brown, Mel (2006). "Early Australian Diving – The Lawson Lung". Historical Diving Society Australia-Pacific. Retrieved 24 August 2017.
- Républic Française. Ministère du Commerce et de l'Industrie. Direction de la Propriété Industrielle. Brevet d'Invention Gr. 6. - Cl. 3. No. 768.083
- Tailliez, Philippe (January 1954). Plongées sans câble (in French). Paris: Editions Arthaud. p. 52.
- Staff. Key to the treasury of the deep: Ohgushi's Peerless Respirators - Unrivalled in the world (PDF). Tokyo: Tokyo submarine industrial company. Archived from the original (PDF) on 21 November 2016. Retrieved 21 November 2016. Copy of an original users'manual by the manufacturers.
- Monday, Nyle C (2004). "Behind the Japanese Mask: The Strange Journey of Ohgushi's Peerless Respirator" (PDF). Historical Diver. Goleta ,California: Historical Diving Society U.S.A. 12 (2 Number 39): 25. ISSN 1094-4516. Retrieved 21 November 2016.
- image #42, Summer 2007, pp5-7, Historical Diving Times
- Rare Vintage Two Hose Regulators (near end of page)
- Seveke, Lothar. "Dräger PA61/II". Das Alte Taucher (in German). Dresden: Lothar Seveke. Retrieved 16 November 2016.
- Andresen, John H, Jr (4 December 1962). "Propulsion system for underwater divers". Patent grant US3066638 A. Arlington, Virginia: United States Patent and Trademark Office. pp. 1–2. Retrieved 17 November 2016.
- "Archived copy" (PDF). Archived from the original (PDF) on 28 September 2007. Retrieved 29 September 2007.CS1 maint: archived copy as title (link)
- French website with images of collected vintage single and twin hose regulators
- Rare Vintage Two Hose Regulators: images
|This diving-related article is a stub. You can help Wikipedia by expanding it.|